[rancid] CatOS

[Gerhard Mourani]

Hello List,

I've some CatOS switches that returns this king of errors messages. Look to me that the command to get configs parameters are not correct or compatible.
Rancid version is 2.3.8 on Linux.

Trying to get all of the configs.
10.18.0.8: missed cmd(s): dir /all slavedisk2:,show rsp chassis-info,show capture,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all sec-
nvram:,show diag chassis-info,dir /all disk2:,show running-config view full,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all disk0:,show
install active,show bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all sec-disk2:,dir /all slavesu
p-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show module,show shun,
show controllers,show diagbus,more system:running-config,dir /all slavedisk0:,show debug,show idprom backplane,dir /all bootflash:,dir /all sup-bootdisk:,dir
/all sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microco
de:,show vlan,dir /all slavebootflash:,show controllers cbus,dir /all slaveslot1:,dir /all nvram:,show version,show vlan-switch,show redundancy secondary,show
running-config,show c7200,dir /all slot1:
10.18.0.8: End of run not found

Gerhard,

[Peter Jackson]

It looks like the device type is set to cisco, but it should be cat5.

Hello List,****
** **
I’ve some CatOS switches that returns this king of errors messages. Look
to me that the command to get configs parameters are not correct or
compatible.****
Rancid version is 2.3.8 on Linux.****
** **
Trying to get all of the configs.****
10.18.0.8: missed cmd(s): dir /all slavedisk2:,show rsp chassis-info,show
capture,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir
/all sec-****
nvram:,show diag chassis-info,dir /all disk2:,show running-config view
full,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all
disk0:,show****
install active,show bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir
/all harddiska:,dir /all slavenvram:,show flash,dir /all sec-disk2:,dir
/all slavesu****
p-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables
boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show
module,show shun,****
show controllers,show diagbus,more system:running-config,dir /all
slavedisk0:,show debug,show idprom backplane,dir /all bootflash:,dir /all
sup-bootdisk:,dir****
/all sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all
sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all
sup-microco****
de:,show vlan,dir /all slavebootflash:,show controllers cbus,dir /all
slaveslot1:,dir /all nvram:,show version,show vlan-switch,show redundancy
secondary,show****
running-config,show c7200,dir /all slot1:****
10.18.0.8: End of run not found****
** **
Gerhard,****
_______________________________________________
Rancid-discuss mailing list
http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss

[Gerhard Mourani]

Hello Peter,

Yes, I've changed cisco for cat5 and now it works. Thanks.

Gerhard,

From: Peter Jackson [mailto:***@gmail.com]
Sent: January-08-13 5:01 PM
To: Gerhard Mourani
Cc: rancid-***@shrubbery.net
Subject: Re: [rancid] CatOS

It looks like the device type is set to cisco, but it should be cat5.
On Tue, Jan 8, 2013 at 1:17 PM, Gerhard Mourani <***@prival.ca<mailto:***@prival.ca>> wrote:
Hello List,

I've some CatOS switches that returns this king of errors messages. Look to me that the command to get configs parameters are not correct or compatible.
Rancid version is 2.3.8 on Linux.

Trying to get all of the configs.
10.18.0.8<http://10.18.0.8>: missed cmd(s): dir /all slavedisk2:,show rsp chassis-info,show capture,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all sec-
nvram:,show diag chassis-info,dir /all disk2:,show running-config view full,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all disk0:,show
install active,show bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all sec-disk2:,dir /all slavesu
p-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show module,show shun,
show controllers,show diagbus,more system:running-config,dir /all slavedisk0:,show debug,show idprom backplane,dir /all bootflash:,dir /all sup-bootdisk:,dir
/all sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microco
de:,show vlan,dir /all slavebootflash:,show controllers cbus,dir /all slaveslot1:,dir /all nvram:,show version,show vlan-switch,show redundancy secondary,show
running-config,show c7200,dir /all slot1:
10.18.0.8<http://10.18.0.8>: End of run not found

Gerhard,