Discussion:
[rancid] Issues with cat5
Ryan DeBerry
2009-01-28 23:12:53 UTC
Permalink
I have seen many posts in the archives with the same issue but I have not
seen a resolution.


clogin works just fine but rancid-run spits out error timeout reached
Michael Stefaniuc
2009-01-29 13:05:22 UTC
Permalink
Post by Ryan DeBerry
I have seen many posts in the archives with the same issue but I have not
seen a resolution.
Which rancid version are you using? I have submitted patches to fix the
problem and those were accepted (in a modified) form upstream. I use
rancid-2.3.2a8 and the only CatOS specific patch I have is to kill the
bogus "set portcost" config lines.
Post by Ryan DeBerry
clogin works just fine but rancid-run spits out error timeout reached
Btw. what device type are you using for the CatOS devices: "cisco" or
"cat5"? "cat5" is the correct type.

bye
michael
--
Michael Stefaniuc Tel.: +49-711-96437-199
Consulting Communications Engineer Fax.: +49-711-96437-111
--------------------------------------------------------------------
Reg. Adresse: Red Hat GmbH, Otto-Hahn-Strasse 20, 85609 Dornach bei Muenchen
Handelsregister: Amtsgericht Muenchen HRB 153243
Geschäftsführer: Brendan Lane, Charlie Peters, Michael Cunningham,
Werner Knoblich
Ryan DeBerry
2009-01-29 14:12:09 UTC
Permalink
Yes, I am using cat5 as the device type. I can run clogin and it works
fine. rancid-run produces the following log.

missed cmd(s): write term all,show port ifindex,show module,dir
sup-microcode:,dir sup-bootflash:,dir bootflash:,dir slot0:,show
version,show flash,show running-config,write term,show boot,dir slot1:,show
inventory raw
: End of run not found


Below is a link to old thread.

http://osdir.com/ml/network.rancid/2008-06/msg00018.html
Post by Michael Stefaniuc
Post by Ryan DeBerry
I have seen many posts in the archives with the same issue but I have not
seen a resolution.
Which rancid version are you using? I have submitted patches to fix the
problem and those were accepted (in a modified) form upstream. I use
rancid-2.3.2a8 and the only CatOS specific patch I have is to kill the
bogus "set portcost" config lines.
Post by Ryan DeBerry
clogin works just fine but rancid-run spits out error timeout reached
Btw. what device type are you using for the CatOS devices: "cisco" or
"cat5"? "cat5" is the correct type.
bye
michael
--
Michael Stefaniuc Tel.: +49-711-96437-199
Consulting Communications Engineer Fax.: +49-711-96437-111
--------------------------------------------------------------------
Reg. Adresse: Red Hat GmbH, Otto-Hahn-Strasse 20, 85609 Dornach bei Muenchen
Handelsregister: Amtsgericht Muenchen HRB 153243
Geschäftsführer: Brendan Lane, Charlie Peters, Michael Cunningham,
Werner Knoblich
Sreekanth K
2009-01-30 16:45:46 UTC
Permalink
Me too have the same problem... I am on 2.3.2a9... Can someone help!!!
Post by Ryan DeBerry
Yes, I am using cat5 as the device type. I can run clogin and it works
fine. rancid-run produces the following log.
missed cmd(s): write term all,show port ifindex,show module,dir
sup-microcode:,dir sup-bootflash:,dir bootflash:,dir slot0:,show
version,show flash,show running-config,write term,show boot,dir slot1:,show
inventory raw
: End of run not found
Below is a link to old thread.
http://osdir.com/ml/network.rancid/2008-06/msg00018.html
Post by Michael Stefaniuc
Post by Ryan DeBerry
I have seen many posts in the archives with the same issue but I have
not
Post by Ryan DeBerry
seen a resolution.
Which rancid version are you using? I have submitted patches to fix the
problem and those were accepted (in a modified) form upstream. I use
rancid-2.3.2a8 and the only CatOS specific patch I have is to kill the
bogus "set portcost" config lines.
Post by Ryan DeBerry
clogin works just fine but rancid-run spits out error timeout reached
Btw. what device type are you using for the CatOS devices: "cisco" or
"cat5"? "cat5" is the correct type.
bye
michael
--
Michael Stefaniuc Tel.: +49-711-96437-199
Consulting Communications Engineer Fax.: +49-711-96437-111
--------------------------------------------------------------------
Reg. Adresse: Red Hat GmbH, Otto-Hahn-Strasse 20, 85609 Dornach bei Muenchen
Handelsregister: Amtsgericht Muenchen HRB 153243
Geschäftsführer: Brendan Lane, Charlie Peters, Michael Cunningham,
Werner Knoblich
_______________________________________________
Rancid-discuss mailing list
http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
--
Best Regards
K Sreekanth
09941914363
Michael Stefaniuc
2009-01-30 17:06:59 UTC
Permalink
Post by Sreekanth K
Me too have the same problem... I am on 2.3.2a9... Can someone help!!!
I'm still on a8 and it works there. It was fixed in a5 or a6 time frame
when the two patches went in. I might upgrade to a9 but I'm pretty busy
at the moment and don't have time for that.

bye
michael
Post by Sreekanth K
Post by Ryan DeBerry
Yes, I am using cat5 as the device type. I can run clogin and it works
fine. rancid-run produces the following log.
missed cmd(s): write term all,show port ifindex,show module,dir
sup-microcode:,dir sup-bootflash:,dir bootflash:,dir slot0:,show
version,show flash,show running-config,write term,show boot,dir slot1:,show
inventory raw
: End of run not found
Below is a link to old thread.
http://osdir.com/ml/network.rancid/2008-06/msg00018.html
Post by Michael Stefaniuc
Post by Ryan DeBerry
I have seen many posts in the archives with the same issue but I have
not
Post by Ryan DeBerry
seen a resolution.
Which rancid version are you using? I have submitted patches to fix the
problem and those were accepted (in a modified) form upstream. I use
rancid-2.3.2a8 and the only CatOS specific patch I have is to kill the
bogus "set portcost" config lines.
Post by Ryan DeBerry
clogin works just fine but rancid-run spits out error timeout reached
Btw. what device type are you using for the CatOS devices: "cisco" or
"cat5"? "cat5" is the correct type.
--
Michael Stefaniuc Tel.: +49-711-96437-199
Consulting Communications Engineer Fax.: +49-711-96437-111
--------------------------------------------------------------------
Reg. Adresse: Red Hat GmbH, Otto-Hahn-Strasse 20, 85609 Dornach bei Muenchen
Handelsregister: Amtsgericht Muenchen HRB 153243
Geschäftsführer: Brendan Lane, Charlie Peters, Michael Cunningham,
Werner Knoblich
Ryan DeBerry
2009-01-30 18:13:26 UTC
Permalink
Yep, it works on a8. I just downgraded and all is good.
Post by Michael Stefaniuc
Post by Sreekanth K
Me too have the same problem... I am on 2.3.2a9... Can someone help!!!
I'm still on a8 and it works there. It was fixed in a5 or a6 time frame
when the two patches went in. I might upgrade to a9 but I'm pretty busy
at the moment and don't have time for that.
bye
michael
Post by Sreekanth K
Post by Ryan DeBerry
Yes, I am using cat5 as the device type. I can run clogin and it works
fine. rancid-run produces the following log.
missed cmd(s): write term all,show port ifindex,show module,dir
sup-microcode:,dir sup-bootflash:,dir bootflash:,dir slot0:,show
version,show flash,show running-config,write term,show boot,dir
slot1:,show
Post by Sreekanth K
Post by Ryan DeBerry
inventory raw
: End of run not found
Below is a link to old thread.
http://osdir.com/ml/network.rancid/2008-06/msg00018.html
Post by Michael Stefaniuc
Post by Ryan DeBerry
I have seen many posts in the archives with the same issue but I have
not
Post by Ryan DeBerry
seen a resolution.
Which rancid version are you using? I have submitted patches to fix the
problem and those were accepted (in a modified) form upstream. I use
rancid-2.3.2a8 and the only CatOS specific patch I have is to kill the
bogus "set portcost" config lines.
Post by Ryan DeBerry
clogin works just fine but rancid-run spits out error timeout reached
Btw. what device type are you using for the CatOS devices: "cisco" or
"cat5"? "cat5" is the correct type.
--
Michael Stefaniuc Tel.: +49-711-96437-199
Consulting Communications Engineer Fax.: +49-711-96437-111
--------------------------------------------------------------------
Reg. Adresse: Red Hat GmbH, Otto-Hahn-Strasse 20, 85609 Dornach bei Muenchen
Handelsregister: Amtsgericht Muenchen HRB 153243
Geschäftsführer: Brendan Lane, Charlie Peters, Michael Cunningham,
Werner Knoblich
john heasley
2009-02-02 19:18:16 UTC
Permalink
Post by Ryan DeBerry
Yep, it works on a8. I just downgraded and all is good.
grumble. There isnt enough info here to determine what the problem is.
Could someone set NOPIPE=YES in your environment and run cat5rancid from
a9 with -d to produce a hostname.raw file. that should provide some
indication of where the failure is.
Post by Ryan DeBerry
Post by Michael Stefaniuc
Post by Sreekanth K
Me too have the same problem... I am on 2.3.2a9... Can someone help!!!
I'm still on a8 and it works there. It was fixed in a5 or a6 time frame
when the two patches went in. I might upgrade to a9 but I'm pretty busy
at the moment and don't have time for that.
bye
michael
Post by Sreekanth K
Post by Ryan DeBerry
Yes, I am using cat5 as the device type. I can run clogin and it works
fine. rancid-run produces the following log.
missed cmd(s): write term all,show port ifindex,show module,dir
sup-microcode:,dir sup-bootflash:,dir bootflash:,dir slot0:,show
version,show flash,show running-config,write term,show boot,dir
slot1:,show
Post by Sreekanth K
Post by Ryan DeBerry
inventory raw
: End of run not found
Below is a link to old thread.
http://osdir.com/ml/network.rancid/2008-06/msg00018.html
Post by Michael Stefaniuc
Post by Ryan DeBerry
I have seen many posts in the archives with the same issue but I have
not
Post by Ryan DeBerry
seen a resolution.
Which rancid version are you using? I have submitted patches to fix the
problem and those were accepted (in a modified) form upstream. I use
rancid-2.3.2a8 and the only CatOS specific patch I have is to kill the
bogus "set portcost" config lines.
Post by Ryan DeBerry
clogin works just fine but rancid-run spits out error timeout reached
Btw. what device type are you using for the CatOS devices: "cisco" or
"cat5"? "cat5" is the correct type.
--
Michael Stefaniuc Tel.: +49-711-96437-199
Consulting Communications Engineer Fax.: +49-711-96437-111
--------------------------------------------------------------------
Reg. Adresse: Red Hat GmbH, Otto-Hahn-Strasse 20, 85609 Dornach bei Muenchen
Handelsregister: Amtsgericht Muenchen HRB 153243
Gesch?ftsf?hrer: Brendan Lane, Charlie Peters, Michael Cunningham,
Werner Knoblich
_______________________________________________
Rancid-discuss mailing list
http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
Loading...