[rancid] Help with "Invalid input detected" and "End of run not found"

Discussion:

Voll, Toivo

2012-04-23 15:25:27 UTC

We have rancid running, but it keeps failing for a large number of switches and I'm having trouble figuring out why. Not all switches of the same model and software fail, and not all the failures are with a particular model or software.

It appears, based on packet captures and logs, that the switches in question for some reason don't understand the rancid issued commands. Below is a sample run, as gleaned from wireshark.

Looking at the hex dump, I don't see anything wrong with commands like "show running-config" followed by 0x0d 0x0a. I can issue them from a CLI just fine. Yet the switch (Catalyst 2950) responds with "% Invalid input detected" in the rancid run.

This is a fairly stock rancid install, and we haven't mucked around with the scripts or commands.

Below is the output from "rancid -d" and below that the ascii dump of the corresponding Wireshark capture. I've replaced the real switchname with "problem-switch.our.domain.edu"

Any pointers on what to look at or try would be welcome.
--
Toivo Voll
Network Engineer
Information Technology Communications
University of South Florida

rancid -d problem-switch.our.domain.edu
executing clogin -t 90 -c"show version;show redundancy secondary;show idprom backplane;show install active;show env all;show rsp chassis-info;show gsr chassis;show diag chassis-info;show boot;show bootvar;show variables boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all slot0:;dir /all disk0:;dir /all slot1:;dir /all disk1:;dir /all slot2:;dir /all disk2:;dir /all harddisk:;dir /all harddiska:;dir /all harddiskb:;dir /all sup-bootdisk:;dir /all sup-bootflash:;dir /all sup-microcode:;dir /all slavenvram:;dir /all slavebootflash:;dir /all slaveslot0:;dir /all slavedisk0:;dir /all slaveslot1:;dir /all slavedisk1:;dir /all slaveslot2:;dir /all slavedisk2:;dir /all slavesup-bootflash:;dir /all sec-nvram:;dir /all sec-bootflash:;dir /all sec-slot0:;dir /all sec-disk0:;dir /all sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir /all sec-disk2:;show controllers;show controllers cbus;show diagbus;show diag;show capture;show module;show spe version;show c7200;show inventory raw;show vtp status;show vlan;show vlan-switch;show debug;show shun;more system:running-config;show running-config view full;show running-config;write term" problem-switch.our.domain.edu
PROMPT MATCH: problem-switch#
HIT COMMAND:problem-switch#show version
In ShowVersion: problem-switch#show version
TYPE = 2900XL
HIT COMMAND:problem-switch#show redundancy secondary
In ShowRedundancy: problem-switch#show redundancy secondary
HIT COMMAND:problem-switch#show idprom backplane
In ShowIDprom: problem-switch#show idprom backplane
HIT COMMAND:problem-switch#show install active
In ShowInstallActive: problem-switch#show install active
HIT COMMAND:problem-switch#show env all
In ShowEnv: problem-switch#show env all
HIT COMMAND:problem-switch#show rsp chassis-info
In ShowRSP: problem-switch#show rsp chassis-info
HIT COMMAND:problem-switch#show gsr chassis
In ShowGSR: problem-switch#show gsr chassis
HIT COMMAND:problem-switch#show diag chassis-info
In ShowGSR: problem-switch#show diag chassis-info
HIT COMMAND:problem-switch#show boot
In ShowBoot: problem-switch#show boot
HIT COMMAND:problem-switch#show bootvar
In ShowBoot: problem-switch#show bootvar
HIT COMMAND:problem-switch#show variables boot
In ShowBoot: problem-switch#show variables boot
HIT COMMAND:problem-switch#show flash
In ShowFlash: problem-switch#show flash
HIT COMMAND:problem-switch#dir /all nvram:
In DirSlotN: problem-switch#dir /all nvram:
HIT COMMAND:problem-switch#dir /all bootflash:
In DirSlotN: problem-switch#dir /all bootflash:
HIT COMMAND:problem-switch#dir /all slot0:
In DirSlotN: problem-switch#dir /all slot0:
HIT COMMAND:problem-switch#dir /all disk0:
In DirSlotN: problem-switch#dir /all disk0:
HIT COMMAND:problem-switch#dir /all slot1:
In DirSlotN: problem-switch#dir /all slot1:
HIT COMMAND:problem-switch#dir /all disk1:
In DirSlotN: problem-switch#dir /all disk1:
HIT COMMAND:problem-switch#dir /all slot2:
In DirSlotN: problem-switch#dir /all slot2:
HIT COMMAND:problem-switch#dir /all disk2:
In DirSlotN: problem-switch#dir /all disk2:
HIT COMMAND:problem-switch#dir /all harddisk:
In DirSlotN: problem-switch#dir /all harddisk:
HIT COMMAND:problem-switch#dir /all harddiska:
In DirSlotN: problem-switch#dir /all harddiska:
HIT COMMAND:problem-switch#dir /all harddiskb:
In DirSlotN: problem-switch#dir /all harddiskb:
HIT COMMAND:problem-switch#dir /all sup-bootdisk:
In DirSlotN: problem-switch#dir /all sup-bootdisk:
HIT COMMAND:problem-switch#dir /all sup-bootflash:
In DirSlotN: problem-switch#dir /all sup-bootflash:
HIT COMMAND:problem-switch#dir /all sup-microcode:
In DirSlotN: problem-switch#dir /all sup-microcode:
HIT COMMAND:problem-switch#dir /all slavenvram:
In DirSlotN: problem-switch#dir /all slavenvram:
HIT COMMAND:problem-switch#dir /all slavebootflash:
In DirSlotN: problem-switch#dir /all slavebootflash:
HIT COMMAND:problem-switch#dir /all slaveslot0:
In DirSlotN: problem-switch#dir /all slaveslot0:
HIT COMMAND:problem-switch#dir /all slavedisk0:
In DirSlotN: problem-switch#dir /all slavedisk0:
HIT COMMAND:problem-switch#dir /all slaveslot1:
In DirSlotN: problem-switch#dir /all slaveslot1:
HIT COMMAND:problem-switch#dir /all slavedisk1:
In DirSlotN: problem-switch#dir /all slavedisk1:
HIT COMMAND:problem-switch#dir /all slaveslot2:
In DirSlotN: problem-switch#dir /all slaveslot2:
HIT COMMAND:problem-switch#dir /all slavedisk2:
In DirSlotN: problem-switch#dir /all slavedisk2:
HIT COMMAND:problem-switch#dir /all slavesup-bootflash:
In DirSlotN: problem-switch#dir /all slavesup-bootflash:
HIT COMMAND:problem-switch#dir /all sec-nvram:
In DirSlotN: problem-switch#dir /all sec-nvram:
HIT COMMAND:problem-switch#dir /all sec-bootflash:
In DirSlotN: problem-switch#dir /all sec-bootflash:
HIT COMMAND:problem-switch#dir /all sec-slot0:
In DirSlotN: problem-switch#dir /all sec-slot0:
HIT COMMAND:problem-switch#dir /all sec-disk0:
In DirSlotN: problem-switch#dir /all sec-disk0:
HIT COMMAND:problem-switch#dir /all sec-slot1:
In DirSlotN: problem-switch#dir /all sec-slot1:
HIT COMMAND:problem-switch#dir /all sec-disk1:
In DirSlotN: problem-switch#dir /all sec-disk1:
HIT COMMAND:problem-switch#dir /all sec-slot2:
In DirSlotN: problem-switch#dir /all sec-slot2:
HIT COMMAND:problem-switch#dir /all sec-disk2:
In DirSlotN: problem-switch#dir /all sec-disk2:
HIT COMMAND:problem-switch#show controllers
In ShowContAll: problem-switch#show controllers
HIT COMMAND:problem-switch#show controllers cbus
In ShowContCbus: problem-switch#show controllers cbus
HIT COMMAND:problem-switch#show diagbus
In ShowDiagbus: problem-switch#show diagbus
HIT COMMAND:problem-switch#show diag
In ShowDiag: problem-switch#show diag
HIT COMMAND:problem-switch#show capture
In ShowCapture: problem-switch#show capture
HIT COMMAND:problem-switch#show module
In ShowModule: problem-switch#show module
HIT COMMAND:problem-switch#show spe version
In ShowSpeVersion: problem-switch#show spe version
HIT COMMAND:problem-switch#show c7200
In ShowC7200: problem-switch#show c7200
HIT COMMAND:problem-switch#show inventory raw
In ShowInventory: problem-switch#show inventory raw
HIT COMMAND:problem-switch#show vtp status
In ShowVTP: problem-switch#show vtp status
HIT COMMAND:problem-switch#show vlan
In ShowVLAN: problem-switch#show vlan
HIT COMMAND:problem-switch#show vlan-switch
In ShowVLAN: problem-switch#show vlan-switch
HIT COMMAND:problem-switch#show debug
In ShowDebug: problem-switch#show debug
HIT COMMAND:problem-switch#show shun
In ShowShun: problem-switch#show shun
HIT COMMAND:problem-switch#more system:running-config
In WriteTerm: problem-switch#more system:running-config
HIT COMMAND:problem-switch#show running-config view full
In WriteTerm: problem-switch#show running-config view full
HIT COMMAND:problem-switch#show running-config
In WriteTerm: problem-switch#show running-config
HIT COMMAND:problem-switch#write term
In WriteTerm: problem-switch#write term
problem-switch.our.domain.edu: End of run not found
problem-switch.our.domain.edu: End of run not found
!

Wiresahark:

problem-switch#
terminal length 0 .
t
e
r
m
i
n
a
l

l
e
n
g
t
h

0

problem-switch#
terminal width 132 .
t
e
r
m
i
n
a
l

w
i
d
t
h

1
3
2

problem-switch#
show version .
s
h
o
w

v
e
r
s
i
o
n

Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA9, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Fri 01-Dec-06 18:22 by weiliu
Image text-base: 0x80010000, data-base: 0x8067A000

ROM: Bootstrap program is C2950 boot loader

problem-switch uptime is 18 weeks, 1 day, 17 hours, 11 minutes
System returned to ROM by power-on
System restarted at 16:26:56 EST Sat Dec 17 2011
System image file is "flash:c2950-i6k2l2q4-mz.121-22.EA9.bin"

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return t
his product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
***@cisco.com.

cisco WS-C2950G-48-EI (RC32300) processor (revision L0) with 19958K bytes of memory.
Processor board ID FOC0746X0WR
Last reset from system-reset
Running Enhanced Image
48 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flas
h-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0E:83:26:7A:C0
Motherboard assembly number: 73-7409-12
Power supply part number: 34-0965-01
Motherboard serial number: FOC07460LLZ
Power supply serial number: PHI07340GKH
Model revision number: L0
Motherboard revision number: A0
Model number: WS-C2950G-48-EI
System serial number: FOC0746X0WR
Configuration register is 0xF

problem-switch#
show redundancy secondary .
s
h
o
w

r
e
d
u
n
d
a
n
c
y

s
e
c
o
n
d
a
r
y

^
% Invalid input detected at '^' marker.

problem-switch#
show idprom backplane .
s
h
o
w

i
d
p
r
o
m

b
a
c
k
p
l
a
n
e

^
% Invalid input detected at '^' marker.

problem-switch#
show install active .
s
h
o
w

i
n
s
t
a
l
l

a
c
t
i
v
e

^
% Invalid input detected at '^' marker.

problem-switch#
show env all .
s
h
o
w

e
n
v

a
l
l

FAN is OK
Internal POWER supply is OK
RPS is NOT present

problem-switch#
show rsp chassis-info .
s
h
o
w

r
s
p

c
h
a
s
s
i
s
-
i
n
f
o

^
% Invalid input detected at '^' marker.

problem-switch#
show gsr chassis .
s
h
o
w

g
s
r

c
h
a
s
s
i
s

^
% Invalid input detected at '^' marker.

problem-switch#
show diag chassis-info .
s
h
o
w

d
i
a
g

c
h
a
s
s
i
s
-
i
n
f
o

^
% Invalid input detected at '^' marker.

problem-switch#
show boot .
s
h
o
w

b
o
o
t

^
% Invalid input detected at '^' marker.

problem-switch#
show bootvar .
s
h
o
w

b
o
o
t
v
a
r

^
% Invalid input detected at '^' marker.

problem-switch#
show variables boot .
s
h
o
w

v
a
r
i
a
b
l
e
s

b
o
o
t

^
% Invalid input detected at '^' marker.

problem-switch#
show flash .
s
h
o
w

f
l
a
s
h

Directory of flash:/

2 -rwx 318 Feb 13 2007 08:37:42 -05:00 env_vars
3 -rwx 796 Feb 28 1993 19:00:33 -05:00 vlan.dat
4 drwx 1536 Feb 28 1993 19:00:15 -05:00 crashinfo
109 -rwx 13683 Jan 11 2012 15:28:49 -05:00 config.text
6 -rwx 1048 Jan 11 2012 15:28:49 -05:00 multiple-fs
7 -rwx 111 Feb 13 2007 08:33:10 -05:00 info
8 -rwx 3707976 Feb 13 2007 08:36:02 -05:00 c2950-i6k2l2q4-mz.121-22.EA9.bin
9 drwx 4160 Feb 13 200
7 08:36:57 -05:00 html
84 -rwx 111 Feb 13 2007 08:37:42 -05:00 info.ver
480 -rwx 2155 Jan 11 2012 15:28:49 -05:00 private-config.text

7741440 bytes total (2133504 bytes free)
problem-switch#
dir /all nvram: .
d
i
r

/
a
l
l

n
v
r
a
m
:

Translating "l"...domain server
(131.247.1.40)
(131.247.100.1)

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all bootflash: .
d
i
r

/
a
l
l

b
o
o
t
f
l
a
s
h
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slot0: .
d
i
r

/
a
l
l

s
l
o
t
0
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all disk0: .
d
i
r

/
a
l
l

d
i
s
k
0
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slot1: .
d
i
r

/
a
l
l

s
l
o
t
1
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all disk1: .
d
i
r

/
a
l
l

d
i
s
k
1
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slot2: .
d
i
r

/
a
l
l

s
l
o
t
2
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all disk2: .
d
i
r

/
a
l
l

d
i
s
k
2
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all harddisk: .
d
i
r

/
a
l
l

h
a
r
d
d
i
s
k
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all harddiska: .
d
i
r

/
a
l
l

h
a
r
d
d
i
s
k
a
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all harddiskb: .
d
i
r

/
a
l
l

h
a
r
d
d
i
s
k
b
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sup-bootdisk: .
d
i
r

/
a
l
l

s
u
p
-
b
o
o
t
d
i
s
k
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sup-bootflash: .
d
i
r

/
a
l
l

s
u
p
-
b
o
o
t
f
l
a
s
h
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sup-microcode: .
d
i
r

/
a
l
l

s
u
p
-
m
i
c
r
o
c
o
d
e
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slavenvram: .
d
i
r

/
a
l
l

s
l
a
v
e
n
v
r
a
m
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slavebootflash: .
d
i
r

/
a
l
l

s
l
a
v
e
b
o
o
t
f
l
a
s
h
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slaveslot0: .
d
i
r

/
a
l
l

s
l
a
v
e
s
l
o
t
0
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slavedisk0: .
d
i
r

/
a
l
l

s
l
a
v
e
d
i
s
k
0
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slaveslot1: .
d
i
r

/
a
l
l

s
l
a
v
e
s
l
o
t
1
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slavedisk1: .
d
i
r

/
a
l
l

s
l
a
v
e
d
i
s
k
1
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slaveslot2: .
d
i
r

/
a
l
l

s
l
a
v
e
s
l
o
t
2
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slavedisk2: .
d
i
r

/
a
l
l

s
l
a
v
e
d
i
s
k
2
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all slavesup-bootflash: .
d
i
r

/
a
l
l

s
l
a
v
e
s
u
p
-
b
o
o
t
f
l
a
s
h
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sec-nvram: .
d
i
r

/
a
l
l

s
e
c
-
n
v
r
a
m
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sec-bootflash: .
d
i
r

/
a
l
l

s
e
c
-
b
o
o
t
f
l
a
s
h
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sec-slot0: .
d
i
r

/
a
l
l

s
e
c
-
s
l
o
t
0
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sec-disk0: .
d
i
r

/
a
l
l

s
e
c
-
d
i
s
k
0
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sec-slot1: .
d
i
r

/
a
l
l

s
e
c
-
s
l
o
t
1
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sec-disk1: .
d
i
r

/
a
l
l

s
e
c
-
d
i
s
k
1
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sec-slot2: .
d
i
r

/
a
l
l

s
e
c
-
s
l
o
t
2
:

^
% Invalid input detected at '^' marker.

problem-switch#
dir /all sec-disk2: .
d
i
r

/
a
l
l

s
e
c
-
d
i
s
k
2
:

^
% Invalid input detected at '^' marker.

problem-switch#
show controllers .
s
h
o
w

c
o
n
t
r
o
l
l
e
r
s

HWIdb = 80E8835C Mngmnt Vlan = C82 *******
Rx Free Pool Size= 01BE
***********PCI Registers***********
CMIC_DMA_STAT = 00202008 CMIC_CONFIG = 000C2B48
CMIC_DMA_DESC0 = A0B43160 CMIC_DMA_DESC1 = A0B431F0
CMIC_DMA_DESC2 = A0B4791C CMIC_DMA_DESC3 = A0B48194
CMIC_IRQ_MASK = 0003FFC8 CMIC_IRQ_STAT = 00080025
CMIC_DMA_CTRL = 00001111 CMIC_SCHAN_CTRL = 0004B042
CMIC_DLF_REG = 0BFFFFFF

******S-Channel Registers******
EGR_BKP_DIS =00000000 MMUPORTENABLE =0BFFFFFF EPC_HOL =00000000

******COS Related Register
s******
******For CosVal.:0 Register Values******
COS_ENABLE = 00000000
******For CosVal.:1 Register Values******
COS_ENABLE = 00000000
******For CosVal.:2 Register Values******
COS_ENABLE = 00000000
******For CosVal.:3 Register Values******
COS_ENABLE = 00000000

******Block Specific Registers******
******For BlockNo.:0 Register Values******
EGR_ENABLE = 000000E8
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For BlockNo.:1 Register Values******
EGR_ENABLE = 000000D1
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For Blo
ckNo.:2 Register Values******
EGR_ENABLE = 000000F2
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For BlockNo.:3 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0BD2D1C8 CONFIG = 401E01D0
******For BlockNo.:4 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0BD2D1C8 CONFIG = 401C01D8

******Port Specific Registers******
******For Port No.:0 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:1 Register Values******
FE_MAC1 = 00000000
FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:2 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:3 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:4 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:5 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCC
COUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:6 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:7 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:8 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:9 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOU
NT = 00000000
******For Port No.:A Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:B Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:C Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:D Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For
Port No.:E Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:F Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:10 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:11 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:12 Register Va
lues******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:13 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:14 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:15 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:16 Register Values******
FE_MAC1 = 0
0000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:17 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:18 Register Values******
GMACC1_GPIC0b = D50A1001 GMACC1_GPIC1b = D50A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:19 Register Values******
GMACC1_GPIC0b = C40A1001 GMACC1_GPIC1b = C40A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_
FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
----------- Tx Queue Status --------------
Ch 1 Status = 1 Ch 2 Status = 1
Ch1 QLen=00 Ch2 QLen=00
----------- Rx Queue Status --------------
Ch1 Status = 4 | Ch2 Status = 0 | Throttle = No
Ch1 Base = A0B47F48 Ch2 Base = A0B486A0
Ch1 End = A0B48038 Ch2 End = A0B48790
Ch1 Rd Ptr = A0B47F48 Ch2 Rd Ptr = A0B48730
Ch1 Alloc Ptr = 00000000 Ch2 Alloc Ptr = 00000000
Forward Mask = 02000000 Utagged bitmap = 00000000

------------ Error Counters --------
PCI Parity Error= 00000000 PCI Fatal Error = 00000000***********PCI Registers***********
CMIC_DMA_STAT = 00202008 CMIC_CONFIG = 000C2B48
CMIC_DMA_DESC0 = A0B43160 CMIC_DMA_DESC1 = A0B43160
CMIC_DMA_DESC2 = A0B487CC CMIC_DMA_DESC3 = A0B49404
CMIC_IRQ_MASK = 0003FFC8 CMIC_IRQ_STAT = 00080025
CMIC_DMA_CTRL = 00001111 CMIC_SCHAN_CTRL = 0004B042
CMIC_DLF_REG = 0BFFFFFF

******S-Channel Registers******
EGR_BKP_DIS =00000000 MMUPORTENABLE =0BFFFFFF EPC_HOL =00000000

******COS Related Registers******
******For CosVal.:0 Register Values******
COS_ENABLE = 00000000
******For CosVal.:1 Register Values******
COS_ENABLE = 00000000
******For CosVal.:2 Register Values******
COS_ENABLE = 00000000
******For CosVal.:3 Register Values******
COS_ENABLE = 00000000

******Block Specific Registers******
******For BlockNo.:0 Register Values******
EGR_ENABLE = 000000B3
EPC_LINK =0AFE1FB3 CONFIG = 401C81D8
******For BlockNo.:1 Register Values******
EGR_ENABLE = 0000001F
EPC_LINK =0AFE1FB3 CONFI
G = 401C81D8
******For BlockNo.:2 Register Values******
EGR_ENABLE = 000000FE
EPC_LINK =0AFE1FB3 CONFIG = 401C81D8
******For BlockNo.:3 Register Values******
GEGR_ENABLE = 00000000
EPC_LINK =0AFE1FB3 CONFIG = 401C01D8
******For BlockNo.:4 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0AFE1FB3 CONFIG = 401E01D0

******Port Specific Registers******
******For Port No.:0 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:1 Register Values*
*****
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:2 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:3 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:4 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:5 Register Values******
FE_MAC1 = 000000
01 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:6 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:7 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:8 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:9 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001

LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:A Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:B Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:C Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:D Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCC
COUNT = 00000000
******For Port No.:E Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:F Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:10 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:11 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******
For Port No.:12 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:13 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:14 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:15 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:16 Register
Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:17 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:18 Register Values******
GMACC1_GPIC0b = C40A1001 GMACC1_GPIC1b = C40A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:19 Register Values******
GMACC1_GPIC0b = D50A1001 GMACC1_GPIC1b = D50A1001
GTH_FE_M
AC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
----------- Tx Queue Status --------------
Ch 1 Status = 1 Ch 2 Status = 1
Ch1 QLen=00 Ch2 QLen=00
----------- Rx Queue Status --------------
Ch1 Status = 4 | Ch2 Status = 0 | Throttle = No
Ch1 Base = A0B48DF8 Ch2 Base = A0B49550
Ch1 End = A0B48EE8 Ch2 End = A0B49640
Ch1 Rd Ptr = A0B48DF8 Ch2 Rd Ptr = A0B49620
Ch1 Alloc Ptr = 00000000 Ch2 Alloc Ptr = 00000000
Forward Mask = 00000000
Utagged bitmap = 00000000

------------ Error Counters --------
PCI Parity Error= 00000000 PCI Fatal Error = 00000000
problem-switch#
show controllers cbus .
s
h
o
w

c
o
n
t
r
o
l
l
e
r
s

c
b
u
s

^
% Invalid input detected at '^' marker.

problem-switch#
show diagbus .
s
h
o
w

d
i
a
g
b
u
s

^
% Invalid input detected at '^' marker.

problem-switch#
show diag .
s
h
o
w

d
i
a
g

^
% Invalid input detected at '^' marker.

problem-switch#
show capture .
s
h
o
w

c
a
p
t
u
r
e

^
% Invalid input detected at '^' marker.

problem-switch#
show module .
s
h
o
w

m
o
d
u
l
e

^
% Invalid input detected at '^' marker.

problem-switch#
show spe version .
s
h
o
w

s
p
e

v
e
r
s
i
o
n

^
% Invalid input detected at '^' marker.

problem-switch#
show c7200 .
s
h
o
w

c
7
2
0
0

^
% Invalid input detected at '^' marker.

problem-switch#
show inventory raw .
s
h
o
w

i
n
v
e
n
t
o
r
y

r
a
w

NAME: "problem-switch", DESCR: "Cisco Catalyst c2950 switch with 48 10/100 BaseTX ports and 2 GBIC (Gigabit Interface Converter) slots"
PID: WS-C2950G-48-EI , VID: L0 , SN: FOC0746X0WR

NAME: "FastEthernet0/1", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/2", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/3", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/4", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/5", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/6", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/7", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/8", DESCR: "10/100BaseTXFast Ethernet"
PID:
, VID: , SN:

NAME: "FastEthernet0/9", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/10", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/11", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/12", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/13", DESCR: "
10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/14", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/15", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/16", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/17", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/18", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/19", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/20", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/21", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/22", DESCR: "10/100BaseTXFast Ethernet"

PID: , VID: , SN:

NAME: "FastEthernet0/23", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/24", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/25", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/26", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEtherne
t0/27", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/28", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/29", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/30", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/31", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID
: , SN:

NAME: "FastEthernet0/32", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/33", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/34", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/35", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/36", DESCR: "10/100BaseTX
Fast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/37", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/38", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/39", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/40", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NA
ME: "FastEthernet0/41", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/42", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/43", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/44", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/45", DESCR: "10/100BaseTXFast Ethernet"
PID:
, VID: , SN:

NAME: "FastEthernet0/46", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/47", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "FastEthernet0/48", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID: , SN:

NAME: "GigabitEthernet0/1", DESCR: "Gigabit Ethernet"
PID: , VID: , SN:

NAME: "GigabitEthernet0/1", DESCR: "C
opper Unshielded twisted pair gigabit ethernet port adapter"
PID: GBIC_T , VID: 20 20 20 20, SN: FHH1327T184

NAME: "GigabitEthernet0/2", DESCR: "Gigabit Ethernet"
PID: , VID: , SN:

problem-switch#
show vtp status .
s
h
o
w

v
t
p

s
t
a
t
u
s

VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 250
Number of existing VLANs : 9
VTP Operating Mode : Transparent
VTP Domain Name : Disabled
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Enabled
MD5 digest : 0xB1 0x28 0x3E 0x51 0x67 0xC2 0x6B 0x66
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
problem-switch#
show vlan .
s
h
o
w

v
l
a
n

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/2
20 VLAN0020 active
110 VLAN0110 active
196 VLAN0196 active Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16, Fa0/17, Fa0/18, Fa0/19, Fa0/
20, Fa0/21
Fa0/22, Fa0/23, Fa0/24, Fa0/25, Fa0/26, Fa0/27, Fa0/28, Fa0/29, Fa0/30, Fa0/31
Fa0/32, Fa0/33, Fa0/34, Fa0/35, Fa0/36, Fa0/37, Fa0/38, Fa0/39, Fa0/40, Fa0/41
Fa0/42, Fa0/43, Fa0/44, Fa0/45, Fa0/46, Fa0/47
614 VLAN0614 active Fa0/48
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-def
ault act/unsup
1005 trnet-default act/unsup
3202 ALC_Network_Mgmt active

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
110 enet 100110 1500 - - - - - 0 0
196 e
net 100196 1500 - - - - - 0 0
614 enet 100614 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
3202 enet 103202 1500 - - - - - 0 0

Remote SPAN VLANs
------------------------------------------------------------------------------

Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------

problem-switch#
show vlan-switch .
s
h
o
w

v
l
a
n
-
s
w
i
t
c
h

^
% Invalid input detected at '^' marker.

problem-switch#
show debug .
s
h
o
w

d
e
b
u
g

problem-switch#
show shun .
s
h
o
w

s
h
u
n

^
% Invalid input detected at '^' marker.

problem-switch#
more system:running-config .
m
o
r
e

s
y
s
t
e
m
:
r
u
n
n
i
n
g
-
c
o
n
f
i
g

^
% Invalid input detected at '^' marker.

problem-switch#
show running-config view full .
s
h
o
w

r
u
n
n
i
n
g
-
c
o
n
f
i
g

v
i
e
w

f
u
l
l

^
% Invalid input detected at '^' marker.

problem-switch#
show running-config .
s
h
o
w

r
u
n
n
i
n
g
-
c
o
n
f
i
g

^
% Invalid input detected at '^' marker.

problem-switch#
write term .
w
r
i
t
e

t
e
r
m

^
% Invalid input detected at '^' marker.

problem-switch#
e
e
x
x

Jonathan Mills

2012-04-23 16:13:54 UTC

Permalink

Manually run 'clogin', watching it connect to the switch and execute
each command that you specified after the "-c" flag. At some point, you
should see the ^ sign and the "Invalid input" error. This will at least
show you where the expect script is messing up.

As for the "End of run not found", you'll want to look at the rancid
script being used. If you installed via RPM, then it will be something
like /usr/libexec/rancid/rancid. Look inside that script, and you'll
see two declared variables, $clean_run and $found_end. If either one
evaluates false, then you'll get this "End of run not found" error.
Trace each occurrence of each of those two variables, and eventually
you'll find some regular expressions. Your error likely relates to one
of those regex's not being quite right for your switch output (as it was
in my case). If you have one switch working, and one switch not, then
manually run

clogin -f /path/to/.cloginrc -c "show running-config" hostname

against each switch. Look carefully at how it exits. Compare with the
regex used by $found_end. My guess is you'll quickly see the difference.

--
Jonathan Mills
Systems Administrator
Renaissance Computing Institute
UNC-Chapel Hill

Post by Voll, Toivo
We have rancid running, but it keeps failing for a large number of switches and I'm having trouble figuring out why. Not all switches of the same model and software fail, and not all the failures are with a particular model or software.
It appears, based on packet captures and logs, that the switches in question for some reason don't understand the rancid issued commands. Below is a sample run, as gleaned from wireshark.
Looking at the hex dump, I don't see anything wrong with commands like "show running-config" followed by 0x0d 0x0a. I can issue them from a CLI just fine. Yet the switch (Catalyst 2950) responds with "% Invalid input detected" in the rancid run.
This is a fairly stock rancid install, and we haven't mucked around with the scripts or commands.
Below is the output from "rancid -d" and below that the ascii dump of the corresponding Wireshark capture. I've replaced the real switchname with "problem-switch.our.domain.edu"
Any pointers on what to look at or try would be welcome.
--
Toivo Voll
Network Engineer
Information Technology Communications
University of South Florida
rancid -d problem-switch.our.domain.edu
executing clogin -t 90 -c"show version;show redundancy secondary;show idprom backplane;show install active;show env all;show rsp chassis-info;show gsr chassis;show diag chassis-info;show boot;show bootvar;show variables boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all slot0:;dir /all disk0:;dir /all slot1:;dir /all disk1:;dir /all slot2:;dir /all disk2:;dir /all harddisk:;dir /all harddiska:;dir /all harddiskb:;dir /all sup-bootdisk:;dir /all sup-bootflash:;dir /all sup-microcode:;dir /all slavenvram:;dir /all slavebootflash:;dir /all slaveslot0:;dir /all slavedisk0:;dir /all slaveslot1:;dir /all slavedisk1:;dir /all slaveslot2:;dir /all slavedisk2:;dir /all slavesup-bootflash:;dir /all sec-nvram:;dir /all sec-bootflash:;dir /all sec-slot0:;dir /all sec-disk0:;dir /all sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir /all sec-disk2:;show controllers;show controllers cbus;show diagbus;show diag;show capture;show module;show spe version;show c7200;show inven

Post by Voll, Toivo
ry raw;show vtp status;show vlan;show vlan-switch;show debug;show shun;more system:running-config;show running-config view full;show running-config;write term" problem-switch.our.domain.edu
PROMPT MATCH: problem-switch#
HIT COMMAND:problem-switch#show version
In ShowVersion: problem-switch#show version
TYPE = 2900XL
HIT COMMAND:problem-switch#show redundancy secondary
In ShowRedundancy: problem-switch#show redundancy secondary
HIT COMMAND:problem-switch#show idprom backplane
In ShowIDprom: problem-switch#show idprom backplane
HIT COMMAND:problem-switch#show install active
In ShowInstallActive: problem-switch#show install active
HIT COMMAND:problem-switch#show env all
In ShowEnv: problem-switch#show env all
HIT COMMAND:problem-switch#show rsp chassis-info
In ShowRSP: problem-switch#show rsp chassis-info
HIT COMMAND:problem-switch#show gsr chassis
In ShowGSR: problem-switch#show gsr chassis
HIT COMMAND:problem-switch#show diag chassis-info
In ShowGSR: problem-switch#show diag chassis-info
HIT COMMAND:problem-switch#show boot
In ShowBoot: problem-switch#show boot
HIT COMMAND:problem-switch#show bootvar
In ShowBoot: problem-switch#show bootvar
HIT COMMAND:problem-switch#show variables boot
In ShowBoot: problem-switch#show variables boot
HIT COMMAND:problem-switch#show flash
In ShowFlash: problem-switch#show flash
HIT COMMAND:problem-switch#show controllers
In ShowContAll: problem-switch#show controllers
HIT COMMAND:problem-switch#show controllers cbus
In ShowContCbus: problem-switch#show controllers cbus
HIT COMMAND:problem-switch#show diagbus
In ShowDiagbus: problem-switch#show diagbus
HIT COMMAND:problem-switch#show diag
In ShowDiag: problem-switch#show diag
HIT COMMAND:problem-switch#show capture
In ShowCapture: problem-switch#show capture
HIT COMMAND:problem-switch#show module
In ShowModule: problem-switch#show module
HIT COMMAND:problem-switch#show spe version
In ShowSpeVersion: problem-switch#show spe version
HIT COMMAND:problem-switch#show c7200
In ShowC7200: problem-switch#show c7200
HIT COMMAND:problem-switch#show inventory raw
In ShowInventory: problem-switch#show inventory raw
HIT COMMAND:problem-switch#show vtp status
In ShowVTP: problem-switch#show vtp status
HIT COMMAND:problem-switch#show vlan
In ShowVLAN: problem-switch#show vlan
HIT COMMAND:problem-switch#show vlan-switch
In ShowVLAN: problem-switch#show vlan-switch
HIT COMMAND:problem-switch#show debug
In ShowDebug: problem-switch#show debug
HIT COMMAND:problem-switch#show shun
In ShowShun: problem-switch#show shun
HIT COMMAND:problem-switch#more system:running-config
In WriteTerm: problem-switch#more system:running-config
HIT COMMAND:problem-switch#show running-config view full
In WriteTerm: problem-switch#show running-config view full
HIT COMMAND:problem-switch#show running-config
In WriteTerm: problem-switch#show running-config
HIT COMMAND:problem-switch#write term
In WriteTerm: problem-switch#write term
problem-switch.our.domain.edu: End of run not found
problem-switch.our.domain.edu: End of run not found
!
problem-switch#
terminal length 0 .
t
e
r
m
i
n
a
l
l
e
n
g
t
h
0
problem-switch#
terminal width 132 .
t
e
r
m
i
n
a
l
w
i
d
t
h
1
3
2
problem-switch#
show version .
s
h
o
w
v
e
r
s
i
o
n
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA9, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Fri 01-Dec-06 18:22 by weiliu
Image text-base: 0x80010000, data-base: 0x8067A000
ROM: Bootstrap program is C2950 boot loader
problem-switch uptime is 18 weeks, 1 day, 17 hours, 11 minutes
System returned to ROM by power-on
System restarted at 16:26:56 EST Sat Dec 17 2011
System image file is "flash:c2950-i6k2l2q4-mz.121-22.EA9.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return t
his product immediately.
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
cisco WS-C2950G-48-EI (RC32300) processor (revision L0) with 19958K bytes of memory.
Processor board ID FOC0746X0WR
Last reset from system-reset
Running Enhanced Image
48 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)
32K bytes of flas
h-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0E:83:26:7A:C0
Motherboard assembly number: 73-7409-12
Power supply part number: 34-0965-01
Motherboard serial number: FOC07460LLZ
Power supply serial number: PHI07340GKH
Model revision number: L0
Motherboard revision number: A0
Model number: WS-C2950G-48-EI
System serial number: FOC0746X0WR
Configuration register is 0xF
problem-switch#
show redundancy secondary .
s
h
o
w
r
e
d
u
n
d
a
n
c
y
s
e
c
o
n
d
a
r
y
^
% Invalid input detected at '^' marker.
problem-switch#
show idprom backplane .
s
h
o
w
i
d
p
r
o
m
b
a
c
k
p
l
a
n
e
^
% Invalid input detected at '^' marker.
problem-switch#
show install active .
s
h
o
w
i
n
s
t
a
l
l
a
c
t
i
v
e
^
% Invalid input detected at '^' marker.
problem-switch#
show env all .
s
h
o
w
e
n
v
a
l
l
FAN is OK
Internal POWER supply is OK
RPS is NOT present
problem-switch#
show rsp chassis-info .
s
h
o
w
r
s
p
c
h
a
s
s
i
s
-
i
n
f
o
^
% Invalid input detected at '^' marker.
problem-switch#
show gsr chassis .
s
h
o
w
g
s
r
c
h
a
s
s
i
s
^
% Invalid input detected at '^' marker.
problem-switch#
show diag chassis-info .
s
h
o
w
d
i
a
g
c
h
a
s
s
i
s
-
i
n
f
o
^
% Invalid input detected at '^' marker.
problem-switch#
show boot .
s
h
o
w
b
o
o
t
^
% Invalid input detected at '^' marker.
problem-switch#
show bootvar .
s
h
o
w
b
o
o
t
v
a
r
^
% Invalid input detected at '^' marker.
problem-switch#
show variables boot .
s
h
o
w
v
a
r
i
a
b
l
e
s
b
o
o
t
^
% Invalid input detected at '^' marker.
problem-switch#
show flash .
s
h
o
w
f
l
a
s
h
Directory of flash:/
2 -rwx 318 Feb 13 2007 08:37:42 -05:00 env_vars
3 -rwx 796 Feb 28 1993 19:00:33 -05:00 vlan.dat
4 drwx 1536 Feb 28 1993 19:00:15 -05:00 crashinfo
109 -rwx 13683 Jan 11 2012 15:28:49 -05:00 config.text
6 -rwx 1048 Jan 11 2012 15:28:49 -05:00 multiple-fs
7 -rwx 111 Feb 13 2007 08:33:10 -05:00 info
8 -rwx 3707976 Feb 13 2007 08:36:02 -05:00 c2950-i6k2l2q4-mz.121-22.EA9.bin
9 drwx 4160 Feb 13 200
7 08:36:57 -05:00 html
84 -rwx 111 Feb 13 2007 08:37:42 -05:00 info.ver
480 -rwx 2155 Jan 11 2012 15:28:49 -05:00 private-config.text
7741440 bytes total (2133504 bytes free)
problem-switch#
dir /all nvram: .
d
i
r
/
a
l
l
n
v
r
a
m
Translating "l"...domain server
(131.247.1.40)
(131.247.100.1)
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all bootflash: .
d
i
r
/
a
l
l
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slot0: .
d
i
r
/
a
l
l
s
l
o
t
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all disk0: .
d
i
r
/
a
l
l
d
i
s
k
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slot1: .
d
i
r
/
a
l
l
s
l
o
t
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all disk1: .
d
i
r
/
a
l
l
d
i
s
k
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slot2: .
d
i
r
/
a
l
l
s
l
o
t
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all disk2: .
d
i
r
/
a
l
l
d
i
s
k
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all harddisk: .
d
i
r
/
a
l
l
h
a
r
d
d
i
s
k
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all harddiska: .
d
i
r
/
a
l
l
h
a
r
d
d
i
s
k
a
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all harddiskb: .
d
i
r
/
a
l
l
h
a
r
d
d
i
s
k
b
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sup-bootdisk: .
d
i
r
/
a
l
l
s
u
p
-
b
o
o
t
d
i
s
k
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sup-bootflash: .
d
i
r
/
a
l
l
s
u
p
-
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sup-microcode: .
d
i
r
/
a
l
l
s
u
p
-
m
i
c
r
o
c
o
d
e
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavenvram: .
d
i
r
/
a
l
l
s
l
a
v
e
n
v
r
a
m
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavebootflash: .
d
i
r
/
a
l
l
s
l
a
v
e
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slaveslot0: .
d
i
r
/
a
l
l
s
l
a
v
e
s
l
o
t
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavedisk0: .
d
i
r
/
a
l
l
s
l
a
v
e
d
i
s
k
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slaveslot1: .
d
i
r
/
a
l
l
s
l
a
v
e
s
l
o
t
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavedisk1: .
d
i
r
/
a
l
l
s
l
a
v
e
d
i
s
k
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slaveslot2: .
d
i
r
/
a
l
l
s
l
a
v
e
s
l
o
t
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavedisk2: .
d
i
r
/
a
l
l
s
l
a
v
e
d
i
s
k
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavesup-bootflash: .
d
i
r
/
a
l
l
s
l
a
v
e
s
u
p
-
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-nvram: .
d
i
r
/
a
l
l
s
e
c
-
n
v
r
a
m
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-bootflash: .
d
i
r
/
a
l
l
s
e
c
-
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-slot0: .
d
i
r
/
a
l
l
s
e
c
-
s
l
o
t
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-disk0: .
d
i
r
/
a
l
l
s
e
c
-
d
i
s
k
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-slot1: .
d
i
r
/
a
l
l
s
e
c
-
s
l
o
t
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-disk1: .
d
i
r
/
a
l
l
s
e
c
-
d
i
s
k
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-slot2: .
d
i
r
/
a
l
l
s
e
c
-
s
l
o
t
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-disk2: .
d
i
r
/
a
l
l
s
e
c
-
d
i
s
k
2
^
% Invalid input detected at '^' marker.
problem-switch#
show controllers .
s
h
o
w
c
o
n
t
r
o
l
l
e
r
s
HWIdb = 80E8835C Mngmnt Vlan = C82 *******
Rx Free Pool Size= 01BE
***********PCI Registers***********
CMIC_DMA_STAT = 00202008 CMIC_CONFIG = 000C2B48
CMIC_DMA_DESC0 = A0B43160 CMIC_DMA_DESC1 = A0B431F0
CMIC_DMA_DESC2 = A0B4791C CMIC_DMA_DESC3 = A0B48194
CMIC_IRQ_MASK = 0003FFC8 CMIC_IRQ_STAT = 00080025
CMIC_DMA_CTRL = 00001111 CMIC_SCHAN_CTRL = 0004B042
CMIC_DLF_REG = 0BFFFFFF
******S-Channel Registers******
EGR_BKP_DIS =00000000 MMUPORTENABLE =0BFFFFFF EPC_HOL =00000000
******COS Related Register
s******
******For CosVal.:0 Register Values******
COS_ENABLE = 00000000
******For CosVal.:1 Register Values******
COS_ENABLE = 00000000
******For CosVal.:2 Register Values******
COS_ENABLE = 00000000
******For CosVal.:3 Register Values******
COS_ENABLE = 00000000
******Block Specific Registers******
******For BlockNo.:0 Register Values******
EGR_ENABLE = 000000E8
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For BlockNo.:1 Register Values******
EGR_ENABLE = 000000D1
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For Blo
ckNo.:2 Register Values******
EGR_ENABLE = 000000F2
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For BlockNo.:3 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0BD2D1C8 CONFIG = 401E01D0
******For BlockNo.:4 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0BD2D1C8 CONFIG = 401C01D8
******Port Specific Registers******
******For Port No.:0 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:1 Register Values******
FE_MAC1 = 00000000
FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:2 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:3 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:4 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:5 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCC
COUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:6 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:7 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:8 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:9 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOU
NT = 00000000
******For Port No.:A Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:B Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:C Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:D Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For
Port No.:E Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:F Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:10 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:11 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:12 Register Va
lues******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:13 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:14 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:15 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:16 Register Values******
FE_MAC1 = 0
0000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:17 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:18 Register Values******
GMACC1_GPIC0b = D50A1001 GMACC1_GPIC1b = D50A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:19 Register Values******
GMACC1_GPIC0b = C40A1001 GMACC1_GPIC1b = C40A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_
FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
----------- Tx Queue Status --------------
Ch 1 Status = 1 Ch 2 Status = 1
Ch1 QLen=00 Ch2 QLen=00
----------- Rx Queue Status --------------
Ch1 Status = 4 | Ch2 Status = 0 | Throttle = No
Ch1 Base = A0B47F48 Ch2 Base = A0B486A0
Ch1 End = A0B48038 Ch2 End = A0B48790
Ch1 Rd Ptr = A0B47F48 Ch2 Rd Ptr = A0B48730
Ch1 Alloc Ptr = 00000000 Ch2 Alloc Ptr = 00000000
Forward Mask = 02000000 Utagged bitmap = 00000000
------------ Error Counters --------
PCI Parity Error= 00000000 PCI Fatal Error = 00000000***********PCI Registers***********
CMIC_DMA_STAT = 00202008 CMIC_CONFIG = 000C2B48
CMIC_DMA_DESC0 = A0B43160 CMIC_DMA_DESC1 = A0B43160
CMIC_DMA_DESC2 = A0B487CC CMIC_DMA_DESC3 = A0B49404
CMIC_IRQ_MASK = 0003FFC8 CMIC_IRQ_STAT = 00080025
CMIC_DMA_CTRL = 00001111 CMIC_SCHAN_CTRL = 0004B042
CMIC_DLF_REG = 0BFFFFFF
******S-Channel Registers******
EGR_BKP_DIS =00000000 MMUPORTENABLE =0BFFFFFF EPC_HOL =00000000
******COS Related Registers******
******For CosVal.:0 Register Values******
COS_ENABLE = 00000000
******For CosVal.:1 Register Values******
COS_ENABLE = 00000000
******For CosVal.:2 Register Values******
COS_ENABLE = 00000000
******For CosVal.:3 Register Values******
COS_ENABLE = 00000000
******Block Specific Registers******
******For BlockNo.:0 Register Values******
EGR_ENABLE = 000000B3
EPC_LINK =0AFE1FB3 CONFIG = 401C81D8
******For BlockNo.:1 Register Values******
EGR_ENABLE = 0000001F
EPC_LINK =0AFE1FB3 CONFI
G = 401C81D8
******For BlockNo.:2 Register Values******
EGR_ENABLE = 000000FE
EPC_LINK =0AFE1FB3 CONFIG = 401C81D8
******For BlockNo.:3 Register Values******
GEGR_ENABLE = 00000000
EPC_LINK =0AFE1FB3 CONFIG = 401C01D8
******For BlockNo.:4 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0AFE1FB3 CONFIG = 401E01D0
******Port Specific Registers******
******For Port No.:0 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:1 Register Values*
*****
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:2 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:3 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:4 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:5 Register Values******
FE_MAC1 = 000000
01 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:6 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:7 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:8 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:9 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:A Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:B Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:C Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:D Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCC
COUNT = 00000000
******For Port No.:E Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:F Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:10 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:11 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******
For Port No.:12 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:13 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:14 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:15 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:16 Register
Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:17 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:18 Register Values******
GMACC1_GPIC0b = C40A1001 GMACC1_GPIC1b = C40A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:19 Register Values******
GMACC1_GPIC0b = D50A1001 GMACC1_GPIC1b = D50A1001
GTH_FE_M
AC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
----------- Tx Queue Status --------------
Ch 1 Status = 1 Ch 2 Status = 1
Ch1 QLen=00 Ch2 QLen=00
----------- Rx Queue Status --------------
Ch1 Status = 4 | Ch2 Status = 0 | Throttle = No
Ch1 Base = A0B48DF8 Ch2 Base = A0B49550
Ch1 End = A0B48EE8 Ch2 End = A0B49640
Ch1 Rd Ptr = A0B48DF8 Ch2 Rd Ptr = A0B49620
Ch1 Alloc Ptr = 00000000 Ch2 Alloc Ptr = 00000000
Forward Mask = 00000000
Utagged bitmap = 00000000
------------ Error Counters --------
PCI Parity Error= 00000000 PCI Fatal Error = 00000000
problem-switch#
show controllers cbus .
s
h
o
w
c
o
n
t
r
o
l
l
e
r
s
c
b
u
s
^
% Invalid input detected at '^' marker.
problem-switch#
show diagbus .
s
h
o
w
d
i
a
g
b
u
s
^
% Invalid input detected at '^' marker.
problem-switch#
show diag .
s
h
o
w
d
i
a
g
^
% Invalid input detected at '^' marker.
problem-switch#
show capture .
s
h
o
w
c
a
p
t
u
r
e
^
% Invalid input detected at '^' marker.
problem-switch#
show module .
s
h
o
w
m
o
d
u
l
e
^
% Invalid input detected at '^' marker.
problem-switch#
show spe version .
s
h
o
w
s
p
e
v
e
r
s
i
o
n
^
% Invalid input detected at '^' marker.
problem-switch#
show c7200 .
s
h
o
w
c
7
2
0
0
^
% Invalid input detected at '^' marker.
problem-switch#
show inventory raw .
s
h
o
w
i
n
v
e
n
t
o
r
y
r
a
w
NAME: "problem-switch", DESCR: "Cisco Catalyst c2950 switch with 48 10/100 BaseTX ports and 2 GBIC (Gigabit Interface Converter) slots"
PID: WS-C2950G-48-EI , VID: L0 , SN: FOC0746X0WR
NAME: "FastEthernet0/1", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/2", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/3", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/4", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/5", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/6", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/7", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/8", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/9", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/10", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/11", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/12", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/13", DESCR: "
10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/14", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/15", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/16", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/17", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/18", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/19", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/20", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/21", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/22", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/23", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/24", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/25", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/26", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEtherne
t0/27", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/28", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/29", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/30", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/31", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID
NAME: "FastEthernet0/32", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/33", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/34", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/35", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/36", DESCR: "10/100BaseTX
Fast Ethernet"
NAME: "FastEthernet0/37", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/38", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/39", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/40", DESCR: "10/100BaseTXFast Ethernet"
NA
ME: "FastEthernet0/41", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/42", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/43", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/44", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/45", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/46", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/47", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/48", DESCR: "10/100BaseTXFast Ethernet"
NAME: "GigabitEthernet0/1", DESCR: "Gigabit Ethernet"
NAME: "GigabitEthernet0/1", DESCR: "C
opper Unshielded twisted pair gigabit ethernet port adapter"
PID: GBIC_T , VID: 20 20 20 20, SN: FHH1327T184
NAME: "GigabitEthernet0/2", DESCR: "Gigabit Ethernet"
problem-switch#
show vtp status .
s
h
o
w
v
t
p
s
t
a
t
u
s
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 250
Number of existing VLANs : 9
VTP Operating Mode : Transparent
VTP Domain Name : Disabled
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Enabled
MD5 digest : 0xB1 0x28 0x3E 0x51 0x67 0xC2 0x6B 0x66
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
problem-switch#
show vlan .
s
h
o
w
v
l
a
n
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/2
20 VLAN0020 active
110 VLAN0110 active
196 VLAN0196 active Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16, Fa0/17, Fa0/18, Fa0/19, Fa0/
20, Fa0/21
Fa0/22, Fa0/23, Fa0/24, Fa0/25, Fa0/26, Fa0/27, Fa0/28, Fa0/29, Fa0/30, Fa0/31
Fa0/32, Fa0/33, Fa0/34, Fa0/35, Fa0/36, Fa0/37, Fa0/38, Fa0/39, Fa0/40, Fa0/41
Fa0/42, Fa0/43, Fa0/44, Fa0/45, Fa0/46, Fa0/47
614 VLAN0614 active Fa0/48
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-def
ault act/unsup
1005 trnet-default act/unsup
3202 ALC_Network_Mgmt active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
110 enet 100110 1500 - - - - - 0 0
196 e
net 100196 1500 - - - - - 0 0
614 enet 100614 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
3202 enet 103202 1500 - - - - - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
problem-switch#
show vlan-switch .
s
h
o
w
v
l
a
n
-
s
w
i
t
c
h
^
% Invalid input detected at '^' marker.
problem-switch#
show debug .
s
h
o
w
d
e
b
u
g
problem-switch#
show shun .
s
h
o
w
s
h
u
n
^
% Invalid input detected at '^' marker.
problem-switch#
more system:running-config .
m
o
r
e
s
y
s
t
e
m
r
u
n
n
i
n
g
-
c
o
n
f
i
g
^
% Invalid input detected at '^' marker.
problem-switch#
show running-config view full .
s
h
o
w
r
u
n
n
i
n
g
-
c
o
n
f
i
g
v
i
e
w
f
u
l
l
^
% Invalid input detected at '^' marker.
problem-switch#
show running-config .
s
h
o
w
r
u
n
n
i
n
g
-
c
o
n
f
i
g
^
% Invalid input detected at '^' marker.
problem-switch#
write term .
w
r
i
t
e
t
e
r
m
^
% Invalid input detected at '^' marker.
problem-switch#
e
e
x
x
i
i
t
t
.
_______________________________________________
Rancid-discuss mailing list
http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss

Voll, Toivo

2012-04-23 18:19:39 UTC

Permalink

Thanks! Following your suggested trail I figured it out.

The "End of run not found" was due to none of the "show config" commands succeeding, and hence there never being an "end" statement which it looked for.

Turns out the root cause had nothing to do with Rancid but was a fat-fingered regexp in our Tacacs+ server code that mucked the privilege level of the rancid user to something other than what it was configured to, and hence the switch really never did recognize the commands.

-Toivo

-----Original Message-----
Sent: Monday, April 23, 2012 12:14 PM
To: Voll, Toivo
Subject: Re: [rancid] Help with "Invalid input detected" and "End of run not
found"
Manually run 'clogin', watching it connect to the switch and execute
each command that you specified after the "-c" flag. At some point, you
should see the ^ sign and the "Invalid input" error. This will at least
show you where the expect script is messing up.
As for the "End of run not found", you'll want to look at the rancid
script being used. If you installed via RPM, then it will be something
like /usr/libexec/rancid/rancid. Look inside that script, and you'll
see two declared variables, $clean_run and $found_end. If either one
evaluates false, then you'll get this "End of run not found" error.
Trace each occurrence of each of those two variables, and eventually
you'll find some regular expressions. Your error likely relates to one
of those regex's not being quite right for your switch output (as it was
in my case). If you have one switch working, and one switch not, then
manually run
clogin -f /path/to/.cloginrc -c "show running-config" hostname
against each switch. Look carefully at how it exits. Compare with the
regex used by $found_end. My guess is you'll quickly see the difference.
--
Jonathan Mills
Systems Administrator
Renaissance Computing Institute
UNC-Chapel Hill

Post by Voll, Toivo
We have rancid running, but it keeps failing for a large number of switches

and I'm having trouble figuring out why. Not all switches of the same model
and software fail, and not all the failures are with a particular model or
software.

Post by Voll, Toivo
It appears, based on packet captures and logs, that the switches in

question for some reason don't understand the rancid issued commands.
Below is a sample run, as gleaned from wireshark.

Post by Voll, Toivo
Looking at the hex dump, I don't see anything wrong with commands like

"show running-config" followed by 0x0d 0x0a. I can issue them from a CLI just
fine. Yet the switch (Catalyst 2950) responds with "% Invalid input detected"
in the rancid run.

Post by Voll, Toivo
This is a fairly stock rancid install, and we haven't mucked around with the

scripts or commands.

Post by Voll, Toivo
Below is the output from "rancid -d" and below that the ascii dump of the

corresponding Wireshark capture. I've replaced the real switchname with
"problem-switch.our.domain.edu"

Post by Voll, Toivo
Any pointers on what to look at or try would be welcome.
--
Toivo Voll
Network Engineer
Information Technology Communications
University of South Florida
rancid -d problem-switch.our.domain.edu
executing clogin -t 90 -c"show version;show redundancy secondary;show

idprom backplane;show install active;show env all;show rsp chassis-
info;show gsr chassis;show diag chassis-info;show boot;show bootvar;show
variables boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all slot0:;dir /all
disk0:;dir /all slot1:;dir /all disk1:;dir /all slot2:;dir /all disk2:;dir /all
harddisk:;dir /all harddiska:;dir /all harddiskb:;dir /all sup-bootdisk:;dir /all
sup-bootflash:;dir /all sup-microcode:;dir /all slavenvram:;dir /all
slavebootflash:;dir /all slaveslot0:;dir /all slavedisk0:;dir /all slaveslot1:;dir /all
slavedisk1:;dir /all slaveslot2:;dir /all slavedisk2:;dir /all slavesup-
bootflash:;dir /all sec-nvram:;dir /all sec-bootflash:;dir /all sec-slot0:;dir /all
sec-disk0:;dir /all sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir /all sec-
disk2:;show controllers;show controllers cbus;show diagbus;show diag;show
capture;show module;show spe version;show c7200;show inven
to

Post by Voll, Toivo
ry raw;show vtp status;show vlan;show vlan-switch;show debug;show

shun;more system:running-config;show running-config view full;show
running-config;write term" problem-switch.our.domain.edu

Post by Voll, Toivo
PROMPT MATCH: problem-switch#
HIT COMMAND:problem-switch#show version
In ShowVersion: problem-switch#show version
TYPE = 2900XL
HIT COMMAND:problem-switch#show redundancy secondary
In ShowRedundancy: problem-switch#show redundancy secondary
HIT COMMAND:problem-switch#show idprom backplane
In ShowIDprom: problem-switch#show idprom backplane
HIT COMMAND:problem-switch#show install active
In ShowInstallActive: problem-switch#show install active
HIT COMMAND:problem-switch#show env all
In ShowEnv: problem-switch#show env all
HIT COMMAND:problem-switch#show rsp chassis-info
In ShowRSP: problem-switch#show rsp chassis-info
HIT COMMAND:problem-switch#show gsr chassis
In ShowGSR: problem-switch#show gsr chassis
HIT COMMAND:problem-switch#show diag chassis-info
In ShowGSR: problem-switch#show diag chassis-info
HIT COMMAND:problem-switch#show boot
In ShowBoot: problem-switch#show boot
HIT COMMAND:problem-switch#show bootvar
In ShowBoot: problem-switch#show bootvar
HIT COMMAND:problem-switch#show variables boot
In ShowBoot: problem-switch#show variables boot
HIT COMMAND:problem-switch#show flash
In ShowFlash: problem-switch#show flash
HIT COMMAND:problem-switch#show controllers
In ShowContAll: problem-switch#show controllers
HIT COMMAND:problem-switch#show controllers cbus
In ShowContCbus: problem-switch#show controllers cbus
HIT COMMAND:problem-switch#show diagbus
In ShowDiagbus: problem-switch#show diagbus
HIT COMMAND:problem-switch#show diag
In ShowDiag: problem-switch#show diag
HIT COMMAND:problem-switch#show capture
In ShowCapture: problem-switch#show capture
HIT COMMAND:problem-switch#show module
In ShowModule: problem-switch#show module
HIT COMMAND:problem-switch#show spe version
In ShowSpeVersion: problem-switch#show spe version
HIT COMMAND:problem-switch#show c7200
In ShowC7200: problem-switch#show c7200
HIT COMMAND:problem-switch#show inventory raw
In ShowInventory: problem-switch#show inventory raw
HIT COMMAND:problem-switch#show vtp status
In ShowVTP: problem-switch#show vtp status
HIT COMMAND:problem-switch#show vlan
In ShowVLAN: problem-switch#show vlan
HIT COMMAND:problem-switch#show vlan-switch
In ShowVLAN: problem-switch#show vlan-switch
HIT COMMAND:problem-switch#show debug
In ShowDebug: problem-switch#show debug
HIT COMMAND:problem-switch#show shun
In ShowShun: problem-switch#show shun
HIT COMMAND:problem-switch#more system:running-config
In WriteTerm: problem-switch#more system:running-config
HIT COMMAND:problem-switch#show running-config view full
In WriteTerm: problem-switch#show running-config view full
HIT COMMAND:problem-switch#show running-config
In WriteTerm: problem-switch#show running-config
HIT COMMAND:problem-switch#write term
In WriteTerm: problem-switch#write term
problem-switch.our.domain.edu: End of run not found
problem-switch.our.domain.edu: End of run not found
!
problem-switch#
terminal length 0 .
t
e
r
m
i
n
a
l
l
e
n
g
t
h
0
problem-switch#
terminal width 132 .
t
e
r
m
i
n
a
l
w
i
d
t
h
1
3
2
problem-switch#
show version .
s
h
o
w
v
e
r
s
i
o
n
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA9,

RELEASE SOFTWARE (fc1)

Post by Voll, Toivo
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Fri 01-Dec-06 18:22 by weiliu
Image text-base: 0x80010000, data-base: 0x8067A000
ROM: Bootstrap program is C2950 boot loader
problem-switch uptime is 18 weeks, 1 day, 17 hours, 11 minutes
System returned to ROM by power-on
System restarted at 16:26:56 EST Sat Dec 17 2011
System image file is "flash:c2950-i6k2l2q4-mz.121-22.EA9.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return t
his product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
cisco WS-C2950G-48-EI (RC32300) processor (revision L0) with 19958K bytes

of memory.

Post by Voll, Toivo
Processor board ID FOC0746X0WR
Last reset from system-reset
Running Enhanced Image
48 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)
32K bytes of flas
h-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0E:83:26:7A:C0
Motherboard assembly number: 73-7409-12
Power supply part number: 34-0965-01
Motherboard serial number: FOC07460LLZ
Power supply serial number: PHI07340GKH
Model revision number: L0
Motherboard revision number: A0
Model number: WS-C2950G-48-EI
System serial number: FOC0746X0WR
Configuration register is 0xF
problem-switch#
show redundancy secondary .
s
h
o
w
r
e
d
u
n
d
a
n
c
y
s
e
c
o
n
d
a
r
y
^
% Invalid input detected at '^' marker.
problem-switch#
show idprom backplane .
s
h
o
w
i
d
p
r
o
m
b
a
c
k
p
l
a
n
e
^
% Invalid input detected at '^' marker.
problem-switch#
show install active .
s
h
o
w
i
n
s
t
a
l
l
a
c
t
i
v
e
^
% Invalid input detected at '^' marker.
problem-switch#
show env all .
s
h
o
w
e
n
v
a
l
l
FAN is OK
Internal POWER supply is OK
RPS is NOT present
problem-switch#
show rsp chassis-info .
s
h
o
w
r
s
p
c
h
a
s
s
i
s
-
i
n
f
o
^
% Invalid input detected at '^' marker.
problem-switch#
show gsr chassis .
s
h
o
w
g
s
r
c
h
a
s
s
i
s
^
% Invalid input detected at '^' marker.
problem-switch#
show diag chassis-info .
s
h
o
w
d
i
a
g
c
h
a
s
s
i
s
-
i
n
f
o
^
% Invalid input detected at '^' marker.
problem-switch#
show boot .
s
h
o
w
b
o
o
t
^
% Invalid input detected at '^' marker.
problem-switch#
show bootvar .
s
h
o
w
b
o
o
t
v
a
r
^
% Invalid input detected at '^' marker.
problem-switch#
show variables boot .
s
h
o
w
v
a
r
i
a
b
l
e
s
b
o
o
t
^
% Invalid input detected at '^' marker.
problem-switch#
show flash .
s
h
o
w
f
l
a
s
h
Directory of flash:/
2 -rwx 318 Feb 13 2007 08:37:42 -05:00 env_vars
3 -rwx 796 Feb 28 1993 19:00:33 -05:00 vlan.dat
4 drwx 1536 Feb 28 1993 19:00:15 -05:00 crashinfo
109 -rwx 13683 Jan 11 2012 15:28:49 -05:00 config.text
6 -rwx 1048 Jan 11 2012 15:28:49 -05:00 multiple-fs
7 -rwx 111 Feb 13 2007 08:33:10 -05:00 info
8 -rwx 3707976 Feb 13 2007 08:36:02 -05:00 c2950-i6k2l2q4-mz.121-

22.EA9.bin

Post by Voll, Toivo
9 drwx 4160 Feb 13 200
7 08:36:57 -05:00 html
84 -rwx 111 Feb 13 2007 08:37:42 -05:00 info.ver
480 -rwx 2155 Jan 11 2012 15:28:49 -05:00 private-config.text
7741440 bytes total (2133504 bytes free)
problem-switch#
dir /all nvram: .
d
i
r
/
a
l
l
n
v
r
a
m
Translating "l"...domain server
(131.247.1.40)
(131.247.100.1)
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all bootflash: .
d
i
r
/
a
l
l
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slot0: .
d
i
r
/
a
l
l
s
l
o
t
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all disk0: .
d
i
r
/
a
l
l
d
i
s
k
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slot1: .
d
i
r
/
a
l
l
s
l
o
t
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all disk1: .
d
i
r
/
a
l
l
d
i
s
k
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slot2: .
d
i
r
/
a
l
l
s
l
o
t
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all disk2: .
d
i
r
/
a
l
l
d
i
s
k
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all harddisk: .
d
i
r
/
a
l
l
h
a
r
d
d
i
s
k
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all harddiska: .
d
i
r
/
a
l
l
h
a
r
d
d
i
s
k
a
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all harddiskb: .
d
i
r
/
a
l
l
h
a
r
d
d
i
s
k
b
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sup-bootdisk: .
d
i
r
/
a
l
l
s
u
p
-
b
o
o
t
d
i
s
k
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sup-bootflash: .
d
i
r
/
a
l
l
s
u
p
-
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sup-microcode: .
d
i
r
/
a
l
l
s
u
p
-
m
i
c
r
o
c
o
d
e
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavenvram: .
d
i
r
/
a
l
l
s
l
a
v
e
n
v
r
a
m
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavebootflash: .
d
i
r
/
a
l
l
s
l
a
v
e
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slaveslot0: .
d
i
r
/
a
l
l
s
l
a
v
e
s
l
o
t
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavedisk0: .
d
i
r
/
a
l
l
s
l
a
v
e
d
i
s
k
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slaveslot1: .
d
i
r
/
a
l
l
s
l
a
v
e
s
l
o
t
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavedisk1: .
d
i
r
/
a
l
l
s
l
a
v
e
d
i
s
k
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slaveslot2: .
d
i
r
/
a
l
l
s
l
a
v
e
s
l
o
t
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavedisk2: .
d
i
r
/
a
l
l
s
l
a
v
e
d
i
s
k
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all slavesup-bootflash: .
d
i
r
/
a
l
l
s
l
a
v
e
s
u
p
-
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-nvram: .
d
i
r
/
a
l
l
s
e
c
-
n
v
r
a
m
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-bootflash: .
d
i
r
/
a
l
l
s
e
c
-
b
o
o
t
f
l
a
s
h
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-slot0: .
d
i
r
/
a
l
l
s
e
c
-
s
l
o
t
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-disk0: .
d
i
r
/
a
l
l
s
e
c
-
d
i
s
k
0
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-slot1: .
d
i
r
/
a
l
l
s
e
c
-
s
l
o
t
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-disk1: .
d
i
r
/
a
l
l
s
e
c
-
d
i
s
k
1
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-slot2: .
d
i
r
/
a
l
l
s
e
c
-
s
l
o
t
2
^
% Invalid input detected at '^' marker.
problem-switch#
dir /all sec-disk2: .
d
i
r
/
a
l
l
s
e
c
-
d
i
s
k
2
^
% Invalid input detected at '^' marker.
problem-switch#
show controllers .
s
h
o
w
c
o
n
t
r
o
l
l
e
r
s
HWIdb = 80E8835C Mngmnt Vlan = C82 *******
Rx Free Pool Size= 01BE
***********PCI Registers***********
CMIC_DMA_STAT = 00202008 CMIC_CONFIG = 000C2B48
CMIC_DMA_DESC0 = A0B43160 CMIC_DMA_DESC1 = A0B431F0
CMIC_DMA_DESC2 = A0B4791C CMIC_DMA_DESC3 = A0B48194
CMIC_IRQ_MASK = 0003FFC8 CMIC_IRQ_STAT = 00080025
CMIC_DMA_CTRL = 00001111 CMIC_SCHAN_CTRL = 0004B042
CMIC_DLF_REG = 0BFFFFFF
******S-Channel Registers******
EGR_BKP_DIS =00000000 MMUPORTENABLE =0BFFFFFF EPC_HOL

=00000000

Post by Voll, Toivo
******COS Related Register
s******
******For CosVal.:0 Register Values******
COS_ENABLE = 00000000
******For CosVal.:1 Register Values******
COS_ENABLE = 00000000
******For CosVal.:2 Register Values******
COS_ENABLE = 00000000
******For CosVal.:3 Register Values******
COS_ENABLE = 00000000
******Block Specific Registers******
******For BlockNo.:0 Register Values******
EGR_ENABLE = 000000E8
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For BlockNo.:1 Register Values******
EGR_ENABLE = 000000D1
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For Blo
ckNo.:2 Register Values******
EGR_ENABLE = 000000F2
EPC_LINK =0BD2D1C8 CONFIG = 401C81D8
******For BlockNo.:3 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0BD2D1C8 CONFIG = 401E01D0
******For BlockNo.:4 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0BD2D1C8 CONFIG = 401C01D8
******Port Specific Registers******
******For Port No.:0 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:1 Register Values******
FE_MAC1 = 00000000
FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:2 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:3 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:4 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:5 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCC
COUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:6 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:7 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:8 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:9 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOU
NT = 00000000
******For Port No.:A Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:B Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:C Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:D Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For
Port No.:E Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:F Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:10 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:11 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:12 Register Va
lues******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:13 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:14 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:15 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:16 Register Values******
FE_MAC1 = 0
0000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:17 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:18 Register Values******
GMACC1_GPIC0b = D50A1001 GMACC1_GPIC1b = D50A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:19 Register Values******
GMACC1_GPIC0b = C40A1001 GMACC1_GPIC1b = C40A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_
FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
----------- Tx Queue Status --------------
Ch 1 Status = 1 Ch 2 Status = 1
Ch1 QLen=00 Ch2 QLen=00
----------- Rx Queue Status --------------
Ch1 Status = 4 | Ch2 Status = 0 | Throttle = No
Ch1 Base = A0B47F48 Ch2 Base = A0B486A0
Ch1 End = A0B48038 Ch2 End = A0B48790
Ch1 Rd Ptr = A0B47F48 Ch2 Rd Ptr = A0B48730
Ch1 Alloc Ptr = 00000000 Ch2 Alloc Ptr = 00000000
Forward Mask = 02000000 Utagged bitmap = 00000000
------------ Error Counters --------
PCI Parity Error= 00000000 PCI Fatal Error = 00000000***********PCI

Registers***********

Post by Voll, Toivo
CMIC_DMA_STAT = 00202008 CMIC_CONFIG = 000C2B48
CMIC_DMA_DESC0 = A0B43160 CMIC_DMA_DESC1 = A0B43160
CMIC_DMA_DESC2 = A0B487CC CMIC_DMA_DESC3 = A0B49404
CMIC_IRQ_MASK = 0003FFC8 CMIC_IRQ_STAT = 00080025
CMIC_DMA_CTRL = 00001111 CMIC_SCHAN_CTRL = 0004B042
CMIC_DLF_REG = 0BFFFFFF
******S-Channel Registers******
EGR_BKP_DIS =00000000 MMUPORTENABLE =0BFFFFFF EPC_HOL

=00000000

Post by Voll, Toivo
******COS Related Registers******
******For CosVal.:0 Register Values******
COS_ENABLE = 00000000
******For CosVal.:1 Register Values******
COS_ENABLE = 00000000
******For CosVal.:2 Register Values******
COS_ENABLE = 00000000
******For CosVal.:3 Register Values******
COS_ENABLE = 00000000
******Block Specific Registers******
******For BlockNo.:0 Register Values******
EGR_ENABLE = 000000B3
EPC_LINK =0AFE1FB3 CONFIG = 401C81D8
******For BlockNo.:1 Register Values******
EGR_ENABLE = 0000001F
EPC_LINK =0AFE1FB3 CONFI
G = 401C81D8
******For BlockNo.:2 Register Values******
EGR_ENABLE = 000000FE
EPC_LINK =0AFE1FB3 CONFIG = 401C81D8
******For BlockNo.:3 Register Values******
GEGR_ENABLE = 00000000
EPC_LINK =0AFE1FB3 CONFIG = 401C01D8
******For BlockNo.:4 Register Values******
GEGR_ENABLE = 00000001
EPC_LINK =0AFE1FB3 CONFIG = 401E01D0
******Port Specific Registers******
******For Port No.:0 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:1 Register Values*
*****
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:2 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:3 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:4 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:5 Register Values******
FE_MAC1 = 000000
01 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:6 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:7 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:8 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:9 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:A Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:B Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:C Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:D Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCC
COUNT = 00000000
******For Port No.:E Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:F Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:10 Register Values******
FE_MAC1 = 00000000 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:11 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******
For Port No.:12 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:13 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:14 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:15 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:16 Register
Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C001
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:17 Register Values******
FE_MAC1 = 00000001 FE_MAC2 = 0000C000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:18 Register Values******
GMACC1_GPIC0b = C40A1001 GMACC1_GPIC1b = C40A1001
GTH_FE_MAC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
******For Port No.:19 Register Values******
GMACC1_GPIC0b = D50A1001 GMACC1_GPIC1b = D50A1001
GTH_FE_M
AC1_GPIC0b =00000000 GTH_FE_MAC1_GPIC1b = 00000000
LCCCOUNT = 00000000 GCCCOUNT = 00000000
----------- Tx Queue Status --------------
Ch 1 Status = 1 Ch 2 Status = 1
Ch1 QLen=00 Ch2 QLen=00
----------- Rx Queue Status --------------
Ch1 Status = 4 | Ch2 Status = 0 | Throttle = No
Ch1 Base = A0B48DF8 Ch2 Base = A0B49550
Ch1 End = A0B48EE8 Ch2 End = A0B49640
Ch1 Rd Ptr = A0B48DF8 Ch2 Rd Ptr = A0B49620
Ch1 Alloc Ptr = 00000000 Ch2 Alloc Ptr = 00000000
Forward Mask = 00000000
Utagged bitmap = 00000000
------------ Error Counters --------
PCI Parity Error= 00000000 PCI Fatal Error = 00000000
problem-switch#
show controllers cbus .
s
h
o
w
c
o
n
t
r
o
l
l
e
r
s
c
b
u
s
^
% Invalid input detected at '^' marker.
problem-switch#
show diagbus .
s
h
o
w
d
i
a
g
b
u
s
^
% Invalid input detected at '^' marker.
problem-switch#
show diag .
s
h
o
w
d
i
a
g
^
% Invalid input detected at '^' marker.
problem-switch#
show capture .
s
h
o
w
c
a
p
t
u
r
e
^
% Invalid input detected at '^' marker.
problem-switch#
show module .
s
h
o
w
m
o
d
u
l
e
^
% Invalid input detected at '^' marker.
problem-switch#
show spe version .
s
h
o
w
s
p
e
v
e
r
s
i
o
n
^
% Invalid input detected at '^' marker.
problem-switch#
show c7200 .
s
h
o
w
c
7
2
0
0
^
% Invalid input detected at '^' marker.
problem-switch#
show inventory raw .
s
h
o
w
i
n
v
e
n
t
o
r
y
r
a
w
NAME: "problem-switch", DESCR: "Cisco Catalyst c2950 switch with 48

10/100 BaseTX ports and 2 GBIC (Gigabit Interface Converter) slots"

Post by Voll, Toivo
PID: WS-C2950G-48-EI , VID: L0 , SN: FOC0746X0WR
NAME: "FastEthernet0/1", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/2", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/3", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/4", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/5", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/6", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/7", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/8", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/9", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/10", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/11", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/12", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/13", DESCR: "
10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/14", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/15", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/16", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/17", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/18", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/19", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/20", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/21", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/22", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/23", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/24", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/25", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/26", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEtherne
t0/27", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/28", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/29", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/30", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/31", DESCR: "10/100BaseTXFast Ethernet"
PID: , VID
NAME: "FastEthernet0/32", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/33", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/34", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/35", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/36", DESCR: "10/100BaseTX
Fast Ethernet"
NAME: "FastEthernet0/37", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/38", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/39", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/40", DESCR: "10/100BaseTXFast Ethernet"
NA
ME: "FastEthernet0/41", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/42", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/43", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/44", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/45", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/46", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/47", DESCR: "10/100BaseTXFast Ethernet"
NAME: "FastEthernet0/48", DESCR: "10/100BaseTXFast Ethernet"
NAME: "GigabitEthernet0/1", DESCR: "Gigabit Ethernet"
NAME: "GigabitEthernet0/1", DESCR: "C
opper Unshielded twisted pair gigabit ethernet port adapter"
PID: GBIC_T , VID: 20 20 20 20, SN: FHH1327T184
NAME: "GigabitEthernet0/2", DESCR: "Gigabit Ethernet"
problem-switch#
show vtp status .
s
h
o
w
v
t
p
s
t
a
t
u
s
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 250
Number of existing VLANs : 9
VTP Operating Mode : Transparent
VTP Domain Name : Disabled
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Enabled
MD5 digest : 0xB1 0x28 0x3E 0x51 0x67 0xC2 0x6B 0x66
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
problem-switch#
show vlan .
s
h
o
w
v
l
a
n
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/2
20 VLAN0020 active
110 VLAN0110 active
196 VLAN0196 active Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6,

Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11

Post by Voll, Toivo
Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16, Fa0/17,

Fa0/18, Fa0/19, Fa0/

Post by Voll, Toivo
20, Fa0/21
Fa0/22, Fa0/23, Fa0/24, Fa0/25, Fa0/26, Fa0/27,

Fa0/28, Fa0/29, Fa0/30, Fa0/31

Post by Voll, Toivo
Fa0/32, Fa0/33, Fa0/34, Fa0/35, Fa0/36, Fa0/37,

Fa0/38, Fa0/39, Fa0/40, Fa0/41

Post by Voll, Toivo
Fa0/42, Fa0/43, Fa0/44, Fa0/45, Fa0/46, Fa0/47
614 VLAN0614 active Fa0/48
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-def
ault act/unsup
1005 trnet-default act/unsup
3202 ALC_Network_Mgmt active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1

Trans2

Post by Voll, Toivo
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
110 enet 100110 1500 - - - - - 0 0
196 e
net 100196 1500 - - - - - 0 0
614 enet 100614 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
3202 enet 103202 1500 - - - - - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
problem-switch#
show vlan-switch .
s
h
o
w
v
l
a
n
-
s
w
i
t
c
h
^
% Invalid input detected at '^' marker.
problem-switch#
show debug .
s
h
o
w
d
e
b
u
g
problem-switch#
show shun .
s
h
o
w
s
h
u
n
^
% Invalid input detected at '^' marker.
problem-switch#
more system:running-config .
m
o
r
e
s
y
s
t
e
m
r
u
n
n
i
n
g
-
c
o
n
f
i
g
^
% Invalid input detected at '^' marker.
problem-switch#
show running-config view full .
s
h
o
w
r
u
n
n
i
n
g
-
c
o
n
f
i
g
v
i
e
w
f
u
l
l
^
% Invalid input detected at '^' marker.
problem-switch#
show running-config .
s
h
o
w
r
u
n
n
i
n
g
-
c
o
n
f
i
g
^
% Invalid input detected at '^' marker.
problem-switch#
write term .
w
r
i
t
e
t
e
r
m
^
% Invalid input detected at '^' marker.
problem-switch#
e
e
x
x
i
i
t
t
.
_______________________________________________
Rancid-discuss mailing list
http://www